Concrete Cutting and Coring Chula Vista CA is the trade you call when a slab, wall, footing, or pool deck has to open up without cracking the rest of the structure. We handle concrete sawing and drilling Chula Vista homeowners and contractors rely on for plumbing reroutes, door and window openings, conduit runs, and equipment pads. One call, one crew, one clean cut.
Concrete Cutting and Coring Chula Vista CA is a specialty concrete service that uses diamond-bladed saws and diamond-tipped core bits to cut, slice, or bore precise openings into existing hardened concrete without jackhammering the whole slab apart. We cut control joints, door and window openings, trench drains, plumbing and electrical penetrations, and anchor holes for posts and equipment. The goal is always the same: clean edges, accurate depth, and zero collateral damage to the surrounding slab, rebar, or wire mesh.
In Chula Vista, most of our calls come from three places. Homeowners in Eastlake and Otay Ranch remodeling kitchens and baths need slab cuts for new drain lines. Contractors working commercial pads near Bayfront and Otay Mesa need core holes for bollards, conduit, and gas lines. And property managers dealing with settling, spalling, or poor drainage need sections removed and replaced without tearing out the whole driveway. That is where concrete cutting near me Chula Vista CA searches usually start, and it is exactly the work we do every week.
Every job is scoped to your cut. Here is what comes standard on a typical concrete cutting and coring job in Chula Vista, and what we add on when the project needs it.
We scan for rebar, post-tension cable, and embedded conduit with GPR and a rebar locator before any blade touches concrete. Then we mark the cut lines with chalk and paint. This step is included on every job because cutting blind is how slabs get ruined.
Wall saws, slab saws, and hand-held saws with diamond blades, wet or dry depending on the location. We cut control joints, door and window openings, trench drains, and full slab sections. Depth is set to your spec, usually 1 to 4 inches for control joints and full-depth for removals.
Diamond core bits from 1 inch to 14 inches, mounted on a stand for walls or a rig for slabs. We core for plumbing, electrical, gas, HVAC, bollards, and anchor bolts. Depth is measured and confirmed before we start, so the hole lands where you need it.
We break out the cut sections, cut rebar flush, and haul the rubble off site. The work area gets vacuumed or swept clean. You get a walkable, workable opening ready for the next trade, not a pile of chunks and dust.
Structural cuts and load-bearing openings usually need a permit in Chula Vista. We tell you upfront whether your job needs one and pull it if it does. That keeps the job legal and keeps you out of trouble at inspection.
If your scope includes a patch or new pour, we handle it. If not, we hand off a clean opening with the edges prepped for the next trade. Either way, you get a clear written scope so nobody is guessing about who does what.
We walk the slab or wall with you, mark the cut lines, and scan for rebar, post-tension cable, and embedded conduit using a GPR unit and rebar locator. On a typical Chula Vista driveway or garage slab, this takes 20 to 30 minutes. You get a firm price before we pull a tool out of the truck.
We snap chalk lines and mark the exact cut path with paint or tape. For core holes, we mark center points and confirm diameter, depth, and angle. If your plumber or electrician has a spec sheet, we work straight off it. If not, we measure twice and confirm with you before the blade touches concrete.
We cut with a Hilti or Makita diamond saw, wet or dry depending on the location. Core drilling uses diamond bits from 1 inch up to 14 inches, mounted on a stand for vertical walls or a rig for slab penetrations. Most residential cuts run two to four hours. Commercial slab cuts can run a full day.
We break out the cut sections, haul the concrete rubble off site, and vacuum or sweep the area clean. Rebar is cut flush with a rebar cutter and capped if it stays in place. You get a clean opening ready for the next trade, whether that is plumbing, electrical, or a new pour.
We walk the job with you, confirm the cut matches the plan, and point out anything the next trade needs to know. If a patch or pour is part of the scope, we schedule it. If not, we hand off a clean, code-correct opening and you are done. Payment is due on completion, no deposit games.
We walk the slab or wall with you, mark the cut lines, and scan for rebar, post-tension cable, and embedded conduit using a GPR unit and rebar locator. On a typical Chula Vista driveway or garage slab, this takes 20 to 30 minutes. You get a firm price before we pull a tool out of the truck.
Cuts door and window openings, wall sections, and thick slabs up to 24 inches deep. Track-mounted for straight, true cuts on vertical and overhead surfaces.
Cuts control joints, small openings, and trench lines in slabs and patios. Runs wet or with a vacuum shroud for dust control in occupied spaces.
Bores 1-inch to 14-inch holes through slabs, walls, and footings. Stand-mounted for walls, anchored for slab penetrations, with depth control to the spec.
Scans for rebar, post-tension cable, and embedded conduit before any cut. This is the tool that keeps us from cutting into steel we cannot see.
Locates steel in the slab and cuts rebar flush when a section is removed. Capped or tied back per the engineer's spec.
Controls silica dust at the blade on every indoor and occupied-space cut. Keeps the air clean and the work area walkable.
A 1990s Eastlake home had a bathroom slab with no access for a new drain line. The homeowner had been told the whole bathroom floor would have to come out, a $6,000 job with a two-week timeline.
After: We scanned the slab, cut a 12-foot trench to the plumber's layout, and cored two 4-inch supply holes. Total on-site time was three hours. The plumber tied in the next day, and the floor patch was poured the day after that.
Book this service →
A general contractor needed 14 core holes through a 6-inch commercial pad for bollards, conduit, and a gas line. The site schedule allowed one day for the work, and a miss would push the whole job back a week.
After: We marked and scanned the pad, then cored all 14 holes in one day. Diameters ranged from 2 inches to 8 inches. Every hole landed on spec, and the site inspection passed the first time.
Book this service →
A Bonita property manager had a 20-foot driveway section that was spalling and holding water against the garage. The slab had cracked in three places and the puddle was getting worse each winter.
After: We cut out the failed section to a sound edge, hauled 4 cubic yards of rubble, prepped the base, and poured a new 20-foot slab that matched the existing finish. Water now drains away from the garage.
Book this service →Most cutting jobs start with a problem the homeowner or contractor is trying to fix. Here are the ones we see most often in Chula Vista and how we handle them.
Ask a pro →We scan for rebar and conduit, cut a clean trench or opening to the plumber's spec, and haul the rubble. The plumber gets a workable opening the same day, and the surrounding slab stays intact.
We confirm the structural spec, cut the opening to size with a wall saw, and cut the rebar clean for the new header and framing. The opening passes inspection the first time.
We cut out the failed section to a sound edge, haul it, and prep the base for a new pour. The new section ties into the existing slab and drains away from the house.
We mark, scan, and core to the engineer's spec, one hole at a time, with depth and diameter confirmed before we start. The GC gets the holes on schedule and the site keeps moving.
$350 - $1,200 for most residential jobs; $180 - $350 per core hole
Concrete cutting and coring pricing in Chula Vista depends on depth, diameter, access, and whether the slab is post-tension. Typical 2026 pricing for residential work runs $350 to $1,200 per job. Core holes run $180 to $350 each. Commercial footings and thick walls price higher because of bit wear and rig setup. We give you a firm written price before we start, and we do not bill hourly. If you want a concrete cutting contractor Chula Vista CA who quotes straight, call us and we will walk your job the same day.
Cutting is almost always cheaper than full demolition and replacement. A $900 slab cut saves a $6,000 floor tear-out. A $250 core hole saves a $2,000 wall demolition. The right cut protects the structure you already have and keeps the rest of the project on schedule.
A 4-inch slab cut is fast and cheap. A 12-inch footing cut takes longer, wears the blade faster, and costs more. Core holes price by diameter and depth: a 2-inch hole through 4 inches of slab is the cheapest; a 14-inch hole through 12 inches of footing is the most expensive.
Get a quote ↗Plain concrete cuts fast. Rebar, wire mesh, and post-tension cable slow the cut and require scanning first. Post-tension slabs add a scanning step and a slower cut path, which raises the price but protects the structure.
Get a quote ↗A driveway cut is easy to reach. A slab cut in a tight backyard behind a fence, or a wall cut on the second floor, takes more setup and more time. Access is often the biggest price swing on a residential job.
Get a quote ↗Wet cutting is faster and cheaper on exterior slabs. Dry cutting with a HEPA vacuum costs more because of the extra equipment and slower blade speed, but it is the only option for occupied interiors and finished floors.
Get a quote ↗“We needed a slab cut for a bathroom remodel and two core holes for new drain lines. The crew showed up on time, scanned for rebar first, and had the cuts done in about three hours. Edges were clean, dust was controlled, and they hauled the rubble. Price matched the quote exactly. Would call them again for any concrete cutting in Eastlake.”
Marisol R.Homeowner, Eastlake
✓ Verified“I run a small GC shop and use these guys for all my slab cuts and core drilling. They show up when they say, they scan before they cut, and they never nick rebar. On a commercial pad near Otay Mesa they cut 14 core holes in one day without a single miss. That kind of reliability is hard to find.”
Dave K.General Contractor, Otay Ranch
✓ Verified“We had a driveway section that was spalling and holding water. They cut out the failed slab, hauled it, and prepped the base for a new pour. The cut line was square and the new section matched the old finish. Tenants stopped complaining about the puddle. Fair price, clean work, no drama.”
Priya S.Property Manager, Bonita
✓ VerifiedMost residential jobs run $350 to $1,200 in 2026, depending on depth, diameter, and access. A single 4-inch core hole through a slab runs $180 to $350. A 20-foot slab cut for a plumbing reroute runs $600 to $1,200. Commercial footings and thick walls price higher because of bit wear and rig setup time.
A typical residential slab cut takes two to four hours on site. Core holes run 20 to 40 minutes each through a 6-inch slab. Larger commercial cuts, like a full trench drain through a parking pad, can run a full day. We give you a time window when we book the job and we hit it.
The best concrete cutting contractor in Chula Vista California is the one who scans before cutting, holds ACI certification, carries CSLB licensing, and cleans up after the job. We have been doing exactly that since 2018. Ask for references in your neighborhood, and we will hand them over without hesitation.
Cosmetic cuts, core holes for utilities, and interior slab openings usually do not need a permit. Structural cuts, load-bearing wall openings, and anything touching a footing or foundation typically do. We tell you upfront which category your job falls into and pull the permit if it is required. No guessing, no surprises at inspection.
Call OR Concrete Contractor Chula Vista at +1 (619) 984-3356 for a same-day estimate on concrete cutting and coring in Chula Vista. We are licensed, bonded, and insured under CSLB, and we have been cutting concrete across San Diego County since 2018. One call, one crew, one clean cut.
Get a Free Quote +16199843356 →Call us at +1 (619) 984-3356 and we will get you on the schedule. Most estimates go out the same day, and we answer questions about thickness, finish, and cure times before you commit to anything. Reach us by phone or email, Monday through Friday, 8:00 to 18:00.